The
following cards were featured on my Facebook Live on August 8, 2021 and feature
Penguin Place Bundle featured on page 33 and the Little Delights stamp set
featured on page 59 of the July – December 2021 Mini Catalog
Be Cool Card
(Thank you to Amy
Koenders for the card design)
Designer Series Paper (DSP): Penguin Playmates – One Penguin punched from the coordinating paper to the punch and four pieces (see photo for patterns used)
Pattern Two - one piece cut to ½” x 5 ½” and one piece cut to 2 ¾” x 4”
Pattern Three – one piece cut to ½” x 3 ½”
Accessories: Adhesive of choice. Penguin Builder Punch, Banners Pick a Punch, Stampin’ Dimensionals,
1.
Adhere
the ½” x 5 ¼” piece of Pattern Two DSP to the 4” x 5 ¼” piece of Basic White
cardstock. Use Memento Ink to stamp the “Season’s
Greetings” sentiment directly above the DSP on the right hand side of the
cardstock and then adhere this piece to the inside of the card base.
2.
Adhere
the 4” x 5 ¼” piece of Pattern One DSP to the card front.
3.
Adhere
the 2 ¾” x 4” piece of Pattern Two DSP to the card front (see photo for
placement)
4.
Punch
the Penguin using the Penguin Builder Punch from the coordinating sheet of DSP .Use
Stampin’ Dimensionals to adhere the Penguin to the lower left corner of the card
front.
5.
Use
the Banners Pick a Punch to punch the end of the ½” x 3 ½” piece of Pattern
Three DSP. Use Memento ink to stamp the “Be
Cool…” sentiment onto the banner close to the punched edge. Adhere the banner to the card front sliding
the left edge under the Penguin.
6. Another Christmas card
ready to go!
Merry Christmas Card
Supplies:
Soft
Seafoam – two pieces; one piece to 2 ¾” x 4 ½” and one piece cut to 1 ½” x 2 ¾”
Designer
Series Paper (DSP): Penguin Playmates –
Patter Two - two pieces; one piece cut to 2 ½”
x 4 ¼” and one piece cut to ½” x 5 ¼”: (see photo for pattern used – NOTE: This is a one way pattern so be sure to cut
in a Landscape orientation)
Accessories: Adhesive of choice, Stampin’ Dimensionals
1. Adhere the ½” x 5 ¼”
piece of Pattern Two DSP to the 4” x 5 ¼” piece of Basic White cardstock. Use Shaded Spruce ink to stamp the “Ho, Ho,
Ho” sentiment directly above the DSP on the right hand side of the
cardstock. Adhere this piece to the
inside of the card base.
2. Adhere the 2 ½” x 4 ¼”
piece of Pattern Two DSP to the 2 ¾” x 4 ½” piece of Soft Seafoam cardstock and
then adhere this piece to the card front (see photo for placement).
3. Use Shaded Spruce ink
to stamp the “Merry Christmas” sentiment onto the 1 ½” x 2 ¾” piece of Soft
Seafoam cardstock. Adhere this piece on
top of the DSP on the card front (See photo for placement)
4. Use Stampin’
Dimensionals to adhere the Polar Bear to the lower left corner of the card front
(see photo for placement).
5. And another Christmas card done!
If
you are having problems visualizing these directions, remember you can see them
created step-by-step on my Facebook Live from August 8th HERE. Enjoy these projects and please share them
with a special friend!
Remember, if you would like to purchase any of the supplies to make these cards, just click the “Shop Now” button above to be taken to my Online Store and don’t forget it’s Sale-a-Bration time for every $50 purchase earns FREE product!!!! Be sure to use the Host Code (also listed above) if your order is under $150 (if your order is over $150 be sure to take advantage of the Host Rewards offered by Stampin’ Up!)
See
you on Sunday, August 15th at 2pm for my next Facebook Live!
No comments:
Post a Comment
Thank you for leaving comments, they are greatly appreciated!